Puls-air is a compact, fuel oil operated workshop and hall heater. It is operated with the patented pulsating combustion, which comes from rocket research. Due to the extremely economical combustion, the heater pays for itself.
You can find the complete Puls-air accessories range here
For mobile use of the Puls-air heaters, e.g. for heating construction sites or tents, please adhere to the following points:
You can either buy or lease your Puls-air workshop heater at a low price.
It has never been so easy to heat your workshop at a low price.*
*Without down payment, residual value 10% of acquisition value (AW) plus VAT, term 48 months, only for Germany. Leasing offer through our partner MMV Leasing GmbH, subject to credit checks, etc. There are no additional costs. The stated leasing rate is the net rate (plus 19% VAT for Germany). Before conclusion of the contract, MMV Leasing carries out a contract acceptance check. 2 Warranty extension and steering wheels cannot be leased and must be ordered separately if necessary. In this case, the freight costs will not be charged again.
Basically you can say:
Puls-air standard with very good insulation 600 m³.
Puls-air Plus up to max 1800 m³ with good insulation, with poor insulation 1000-1200 m³.
Very well insulated are halls or workshops built up to 5 years ago. This means insulating glazing, gas concrete walls or sandwich panels 100 mm or 120 mm.
Poorly insulated halls, for example, are just masonry buildings with poor roof.
Room temperature as desired. Based on empirical values, the room temperature of the workshop can be reduced by approx. 4 degrees, while maintaining the same comfort level for the employees, because the heat comes from below. Compared to ceiling fans from above, therefore energy is senselessly wasted.
Yes, because a room thermostat is built into the unit, which automatically turns the unit off and on to maintain the set temperature.
The external fuel oil tank is to be obtained from the local heating contractor. Requirements: Double walled, leak detection & fire protection valve.
No, the unit can be connected to an external fuel oil tank via 8mm copper pipe. Attention: No return - single line system. The tank can be up to 30 m away and the height difference must be max. 3.5 m.
The advantage of the canister is that the device is immediately ready for use.
Approx. 57 dBa, measured in a reference room. The actual noise sensation in a normally equipped workshop or hall is a pleasant light hum.
Puls-air Standard: 1.5 l/h at the economy level and 1.9 l/h at the full power level
Puls-air Plus: 1.9 l/h at the economy level and 2.5 l/h at the full power level
Attention: Do not calculate on the complete day, because the device always switches itself on and off by the thermostat to maintain the temperature.
We always ask the counter question: How much do you need at the moment? - From this minus 50% and then you have the sum (All in approximate figures)
Yes, but this must be connected by us according to the circuit diagram, because the fan must run after.
App control is possible. Your local electrician should contact us in this regard!
Basically there are 2 models: Puls-air Standard (up to 600m³) and Puls-air Plus (with good insulation up to 1,800m³). For even larger premises, 2 or more units can be operated together. Thus, even larger halls and workshops can be heated efficiently and economically.
All prices on this website are exclusive of VAT. Delivery to AUT, ITA and GER costs 90 €. Customers from Switzerland pay 195 € incl. customs clearance.
180 W or 0.18 KW i.e. 0.18 KWh power consumption per hour
Operation of heaters with waste oil under 50 kW is prohibited. Diesel or fuel oil serve as fuel for Puls-air.
32 x 1.5mm wall thickness = 35mm outer diameter
8mm outer diameter
The exhaust pipes are not included and must be ordered separately. Via this link you will get to the assortment.
We will be happy to inform you about the current delivery times by mail, Whatsapp or phone.
Exhaust gas values (NOX - 25 - 30, CO - 2 - 5 ppm; soot number 00)